Remove wheels from vehicle. Inspect vehicle brakes. Remove and install a new tires on to the wheels. Balance the tires. Install the wheels onto the vehicle and torque lug nuts to manufacturer's specifications. Perform TPMS relearn when needed.
Inspect vehicle exterior lighting. Check under hood fluids and top off with manufacturer specified fluid(s). Check engine air filter and serpentine belt(s). Drain vehicle engine oil. Check tire pressure and fill to manufacturer's specifications. Perform visual inspection of the vehicle suspension and underbody. Check vehicle drivetrain fluids when needed. Fill engine with 6.0 quarts of Amsoil full-synthetic engine oil. Recheck engine oil level.
JILL & JAMIE B. gave our service a 5 star review on 1/11/2024
2021 Kia Telluride CRM Mitchell1
2024-01-12T23:02:58+00:00
Remove wheel from vehicle when needed. Locate the leak in the tire. Remove the tire from the wheel. Clean the inside tire surface and install a patch plug into the leak found in the tire. Mount the tire onto the wheel and rebalance. Install tire back onto the vehicle when needed. Perform TPMS relearn when needed.
IRENE & LARRY C. gave our service a 5 star review on 1/8/2024
Inspect vehicle exterior lighting. Check under hood fluids and top off with manufacturer specified fluid(s). Check engine air filter and serpentine belt(s). Drain vehicle engine oil. Check tire pressure and fill to manufacturer's specifications. Perform visual inspection of the vehicle suspension and underbody. Check vehicle drivetrain fluids when needed. Fill engine with 5.0 quarts of Amsoil full-synthetic engine oil. Recheck engine oil level.
Rotate tires, check & set air pressure, check wear pattern.
Access cabin filter housing. Remove the old air filter. Clean out housing of debris. Install new filter. Reassemble all other related components.
JOHANNA C. gave our service a 5 star review on 1/5/2024
2021 Chevrolet TrailBlazer CRM Mitchell1
2024-01-09T23:02:33+00:00
NEED ALL CUSTOMER AND VEHICLE INFO!!! BALL JOINT LEFT SIDE
Disconnect required suspension to access the axle shaft. Remove and replace the axle shaft assembly. Reassemble all Related components.
Separate the lower control arm lower ball joint as need and unbolt the lower control arm assembly. Reassemble with new lower control arm as well as new bushings and lower ball joint assemblies if needed. Reassemble all other related components.
Inspect vehicle exterior lighting. Check under hood fluids and top off with manufacturer specified fluid(s). Check engine air filter and serpentine belt(s). Drain vehicle engine oil. Check tire pressure and fill to manufacturer's specifications. Perform visual inspection of the vehicle suspension and underbody. Check vehicle drivetrain fluids when needed. Fill engine with 4.0 quarts of Quaker State semi-synthetic engine oil. Recheck engine oil level.
BAKAR H. gave our service a 5 star review on 1/5/2024
2009 Chevrolet Impala CRM Mitchell1
2024-01-09T23:02:18+00:00
Inspect vehicle exterior lighting. Check under hood fluids and top off with manufacturer specified fluid(s). Check engine air filter and serpentine belt(s). Drain vehicle engine oil. Check tire pressure and fill to manufacturer's specifications. Perform visual inspection of the vehicle suspension and underbody. Check vehicle drivetrain fluids when needed. Fill engine with 4.5 quarts of Amsoil full-synthetic engine oil. Recheck engine oil level.
Rotate tires, check & set air pressure, check wear pattern.
AUDREY Z. gave our service a 5 star review on 12/29/2023
Disassemble any engine shields and engine control components to access the ignition system. Remove the ignition coils to access the spark plugs. Remove and replace the engine spark plugs. Reassemble all related components. Recheck for proper ignition operation.
Remove and replace right outer upper and lower tie rod ends. Recheck for proper operation.
Place vehicle on alignment rack, attach equipment, measure caster, camber and toe. Compare to vehicle specifications. Set and adjust all approved alignment angles with allowable specifications.
Inspect vehicle exterior lighting. Check under hood fluids and top off with manufacturer specified fluid(s). Check engine air filter and serpentine belt(s). Drain vehicle engine oil. Check tire pressure and fill to manufacturer's specifications. Perform visual inspection of the vehicle suspension and underbody. Check vehicle drivetrain fluids when needed. Fill engine with 7.0 quarts of Quaker State semi-synthetic engine oil. Recheck engine oil level.
Rotate tires, check & set air pressure, check wear pattern.
MIKE STANAITIS A. gave our service a 5 star review on 12/23/2023
2020 Ford F-250 Super Duty CRM Mitchell1
2023-12-24T23:01:15+00:00
Disassemble the rear brake calipers and mounting brackets. Remove the rear brake rotors and clean the rotor mounting surfaces. Clean the caliper slides and lubricate. Reassemble the rear brakes with new brake pads and brake rotors. Test drive for proper braking operation.
Inspect vehicle exterior lighting. Check under hood fluids and top off with manufacturer specified fluid(s). Check engine air filter and serpentine belt(s). Drain vehicle engine oil. Check tire pressure and fill to manufacturer's specifications. Perform visual inspection of the vehicle suspension and underbody. Check vehicle drivetrain fluids when needed. Fill engine with 4.5 quarts of Amsoil full-synthetic engine oil. Recheck engine oil level.
Rotate tires, check & set air pressure, check wear pattern.
Use a scan tool to access the electronic brake control system. Enable and recalibrate the electronic brake control brake calipers for new brake instillation. Recheck for proper braking operation.
GARRY S. gave our service a 5 star review on 12/22/2023